DM311 DATASHEET PDF

DM – Download as PDF File .pdf), Text File .txt) or read online. DM Datasheet, DM PDF, DM Data sheet, DM manual, DM pdf, DM, datenblatt, Electronics DM, alldatasheet, free, datasheet. DM Datasheet PDF Download – Green Mode Fairchild Power Switch, DM data sheet.

Author: Mazushura Shakagor
Country: Sweden
Language: English (Spanish)
Genre: Education
Published (Last): 12 October 2013
Pages: 257
PDF File Size: 17.34 Mb
ePub File Size: 9.75 Mb
ISBN: 150-6-54886-729-5
Downloads: 89275
Price: Free* [*Free Regsitration Required]
Uploader: Goltikazahn

Than the rest is taken down to voltage we want with zener and the IC is fed with that. But I don’t understand the purpose of the resistor, why have it there at all if the DM can handle up to v on Vstr?

Green Mode Fairchild Power Switch (FPSTM)

Anyway, thanks for your valuable input, I see these PSUs quite a lot, but never had time to dive so much much into these tanks of shit And shorted shottky diode on secondary side, I wonder if that was what killed the primary, or the other way around? D,311 as well as 24. Starter for 10 newbie question I have tested the DM using primary ground – neg leg on Big cap.

Step 7 – Generation of driver code. A minimum throughput rate of KHz Is achieved while only dissipating 1.

I don’t know how much the zener can handle but I won’t expect much more than 50 V, than the current through it would be too high.

Please keep us posted. Than the zener is supposed to do datssheet the work and can go short…. Originally Posted by selldoor: Worked great and no more 5vsb headaches. However, what usually goes bad because of excessive overheating due to using that GP diode and no cooling, and because of poor quality, is the cap. Do I still have to use primary ground for this?

  EPICONDYLITIS HUMERI RADIALIS PDF

A potentiometer tied between the 1.

It is notinductance. These services include sameday shipping on orders received prior to 8 p. CT as well as hour customer service and technical support from 6 p.

DataSheet: DM311

I am now going to test CM well some pins Do I still have to use primary ground for this? So I think huge resistor dataasheet there to ensure slow enough charging of the Vcc cap otherwise there would be huge spike through the IC, auxiliary transformer windig and to the cap. If Vcc drops to 7 volts or below, the chip turns off. Statistics are great for politicians.

Typical operation on this power supply, it should reach and maintain 12 volts.

Originally Posted by Behemot: It had multiple problems. That is under normal operation though, if the DM draws more than 3 mA md311 it should, there can be higher drop on it than on the resistor. The Vstr resistor is a current limiter. So there should be some V drop with zener dropping it further to 20 V. I did a comprehansive study on this power supply board a few years ago.

It used to be problem though you CAN squeeze at least 16V D10 caps in there and one or two on other rails with some effort.

  ARMEEBUCH ZWERGE PDF

Vfb The feedback voltage pin is the inverting input to the PWM comparator with nominal input. I have not seen a PSU of this type where they were not so replacing them is a must.

Oh my bad, I’ve been talking about Vcc…the Vstr should consume uA. Measure it and let us know what you get. But digging further it looks alright. Originally Posted by everell: And here are some drawings Attached: Than it should be more than 70 V. Perhaps the large capxon cap started to go bad, and the PFC circuit worked harder to maintain the voltage, overheating the PFC coil and shorting out the DM from high voltage spikes?

AsynchroSerial’ window Step 7 – Generation d,311 driver code. CodeWarrior CD for the latest up-to-date information. No abstract text available Text: There is chance the PWM is bad as well. That’s why I was surprised at first, I assumed I would be reading v here and that the resistor was bad.

DM Datasheet, DM PDF Schematic, Manual, Equivalent – Fairchild Semiconductor

Step 8 – Datashet of the files. I have tens of them with bad caps only so at least for me, statistically, that is minority. Also if something is bad on the 5vsb line, it can load the transformer such that the feedback winding voltage never goes above 9 volts.