HORMANN UAP1 PDF

Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Mauzshura Diramar
Country: Cyprus
Language: English (Spanish)
Genre: Relationship
Published (Last): 10 May 2018
Pages: 438
PDF File Size: 7.97 Mb
ePub File Size: 20.98 Mb
ISBN: 679-7-79207-941-4
Downloads: 25837
Price: Free* [*Free Regsitration Required]
Uploader: Meztibar

Looking at the other link for the Hormann website using translation – it looks like they indicate it can do a partial open: Move the door into the desired position with the buttons andvia the taught-in radio code impulse or an external control element with impulse function.

I am an electronics amateur and can’t figure out based on the schematic below if that is correct? The only things I get from what is stated is that if you press to open – you press the button again to stop it not a true move up move down motion. At startup the Master scans the bus for devices.

Home Questions Tags Users Unanswered. RX When the board is powered while the logic analyzer is collecting data, we see these bytes comming in: In my case it starts at address 0x8D which is in decimal. Later I captured traces using my logic analyzer for each possible command, these are: That way I’m able to trace the bus in realtime without the need to leave the house It’s pretty cold outside at this time of the year.

To control the door via a home automation system you have several options:. Usa a UAP1, a small extension box to have better control over the motor and get some feedback signals.

  LA MIGALA JUAN JOSE ARREOLA PDF

Light on Bit 1: Dominik Hadl 51 4. To dig deaper into the protocoll I need more data.

I expected a rather simple protocoll where no comunication happens until the UAP1 gets triggered by a switch, but I was more than wrong. I found this guidewhich made the setup easier and I’ve setup everything accordingly. Broadcast status From the beginning the master sends a broadcast status message.

By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. I used the CRC calculator at http: I searched the internet for information about the bus, but little to nothing can be found about it. As you ua;1 see the only status bit set, is from the second byte and means reversing according to the patent which makes no sense to me.

Thanks for looking into this! If the selected height is too low, a 2-digit number starting with 1 will appear with a flashing decimal point see section Fortunately the hoormann gives you a nice lookup table for the CRC values which I then used in my Python program to verify all the messages I’ve recorded so far.

Hörmann Universaladapterplatine UAP 1

In my case the UAP1 answers: Unfortunately no other communication is happening when I trigger a “close door” for example. Intelligent contol panels I hoped to find the signals there as well but it turned out that is not the case.

After having discussed that issue with my Italian friend he was able to figure out the polynom 0x07 as well as the initial value 0xF3 for the CRC algorithm. It decrements this address and scans the entire bus.

The description in the patents is not cristal clear at least to me but still extremely helpful in figureing out whats going on on the bus.

  EDUARDO GALEANO OPEN VEINS OF LATIN AMERICA PDF

Reverse engeneering the Hörmann UAP1 protocoll

Learning button assignment Bit 7: RS is Half-Duplex, that means that only one up1 on the bus can talk at a given time. Currently I send a 0. It seems that this must happen when the UAP1 is connected to the motor. This question came from our site for electronics and electrical engineering professionals, students, and enthusiasts. Post as a guest Name.

Hörmann Universaladapterplatine UAP 1 | eBay

These are the messages I was able to make sense of so far. For that to work I needed to buy a UAP universal adapter, meant for uses like these and connect it to my Loxone miniserver.

When the board is powered while the logic analyzer is collecting data, we see these bytes comming in:. The changed partial opening position is saved. Bottom side of the circuit board: Sign up or log in Sign up using Google. Press the PRG button until the decimal point next to the menu number is illuminated. Exactly what I want to have: I decided to look at the boards communications without the motor connected. Reserved Messages These are the messages I was able to make sense of so far.

Not specified in the patent Why it doesnt scan the adresses down to ? A message is always formed like this: Option relay on Bit 3: After being able to seperate the byte stream into messages, I still wasn’t able to calculate the checksum. Email Required, but never shown. Ken 4, 1 4 Drives at least the three relais, maybe more.

Unfortunately the patent doesn’t say anything about the device codes.