This item is no longer available. Suggested replacements. UVAS sc Probe, 1 mm, with SC Controller · Get Quote. Continuous UV Results 1 – 20 of Search results for sc Amtax sc Ammonium Analyzer, mg/L NH₄-N, V, 5 m Filterprobe sc. This item is no longer available. Suggested replacements. UVAS sc Sensor, 5 mm, with SC Controller · Get Quote. Continuously protect plant treatment.
|Published (Last):||21 March 2016|
|PDF File Size:||1.78 Mb|
|ePub File Size:||7.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Troubleshooting Section 7 Troubleshooting The incident light Method of Detection beam is composed of a tungsten filament light source with a color temperature sc1100 and K. The calibration history log shows the gain value, the time and date of the calibration, and the initials of the operator performing verification. The frequency will depend on the nature and concentration of dissolved and suspended solids in the sample. Wear cotton gloves to protect your hands and to avoid fingerprints on the bulb.
Instrument Setup Operation 4. Measurement Hac Transfer 4. In the United States: Troubleshooting Troubleshooting Table 11 presents sensor warnings displayed in the Event Log, possible causes, and corrective actions.
Hach-Lange SC User Manual | 58 pages
Allow at least mm Section 1 Specifications Section 1 Specifications Specifications are subject to change without notice. Please contact the Hach Service Center serving your location. Hacn Table 11 presents sensor warnings displayed in the Event Log, possible causes, and corrective actions.
Turbidimeter Installation Information Installation 3. Section 7 Troubleshooting 7. Index Scc100 Line Installation Page 23 Allow at least mm Do not touch the new bulb with bare hands. Section 1 Specifications Specifications are subject to change without notice.
hxch System Startup Two types of verifications are offered. To ensure that the protection provided by this equipment is not impaired, do not use or install this equipment in any manner other than that specified in this manual. The display will flash on startup, when the hold outputs function has been activated, and when the filter function signal average is changed to a different value.
See Replacement Parts and Accessories on page 55 for ordering information. By pressing ‘print’ ssc100 you will print only current page. Comments to this Manuals Your Name. Index Index Numerics 90 Degree Detector Failure to do so could result in serious injury to the operator or damage to the equipment. Relay loads must be resistive.
Hach sc100 1720E Instrument Manual
Under normal use, Hach recommends replacing the lamp once a year to maintain peak performance. Inadequate bubble removal from Increase the signal averaging time to a longer interval. Remove the quick connect fitting and wires and install the threaded plug on the opening to maintain the environmental rating.
Changing The Sensor Name Operation 4. Failed fuses are an indication that an equipment problem could exist. Enter text from picture: Page 71 Index Sample Line Installation Section 10 Repair Service Authorization must be obtained from Hach Company before sending any items for repair.
The event log stores a variety of events that occur on the devices such as configuration changes, alarms, and warning conditions. To hold the output until released: Dry Verification System Startup Two types of verifications are offered.
The controller contains three relays designed for use with high voltage Danger: Rinse with deionized water before calibrating. Restore sample flow to the instrument. Don’t have an account?
Maintenance Fuse Replacement The controller contains two mains fuses. Section 7 Troubleshooting Section 7 Troubleshooting 7. Wet Verification System Startup 5.
Maximum cable length is 9. Sensor Setup Menu Operation 4. Refer to Figure 29 and perform the following steps to replace the fuses: Page 20 Installation 3.
Hach-Lange SC 100 User Manual
Drain body and clean the body and bubble trap. Twist the bulb in a counterclockwise direction, pulling out slightly, until it is released from the housing. Disconnect and remove the existing wires between the quick hzch and terminal block J5, see Figure 21 on page 4. Section 11 Limited Warranty In the event that a defect is discovered during the warranty period, Hach Company agrees that, at its option, it will repair or replace the defective product or refund the purchase price, subject to the pro-rated schedule above, excluding original shipping wc100 handling charges.
Table of Contents Section 1 Specifications In the event that a defect is discovered during the warranty period, Hach Company agrees that, at its option, it will repair or replace the defective product or refund the purchase price, subject to the pro-rated schedule above, excluding original shipping and handling charges.
Controller Dimension Illustrations Installation 3.