Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopen®, which make them easily scalable to meet requirements for both.
|Published (Last):||8 May 2005|
|PDF File Size:||1.8 Mb|
|ePub File Size:||1.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
2pcs EPEC 2024 ECU Plug 35 Car Waterproof Connector 776273 – 1 770680 – 1 and Termina
All cables, connectors and tools must be of correct type and sufficiently high quality. Copying of this document without permission is prohibited.
This illustrates the normal way to connect loads when load current measurement is desired. No saving operations program flashing or parameter storing into permanent memory can be done under 11,5 VDC. The manufacturer does not guarantee that this product complies any other certification, standard or test than listed below. The maximum rating is lowered in this case to 15 volts.
The application program is provided with frequency and number of the pulses seen in the input in addition to the normal input state.
Memory functions shall remain class A. The result is a two channel pulse counter which is capable of detecting the direction of the movement of the sensor. Inputs are divided into groups by the input impedance configuration. The Color display needs extra facilities in order to have the limit B covered. This feature is useful when driving proportionally controlled loads, e. These parameters depend on software cycle time. After starting up the module measures only the pulse frequency.
This feature makes it possible to detect open loads and short circuits to the supply voltage.
Mounting position horizontal or vertical to allow water etc. We believe that we know control systems for challenging conditions and we are able to offer a total solution from control units to project services and designing. Epwc buyer shall compensate the manufacturer to the extent that the manufacturer might be liable to pay damages as a result of claims based on product liability according to paragraph above. The shutdown circuit is activated when voltage reaches circa 32 V.
Epec Control Module, Epec Control Module Suppliers and Manufacturers at
The downloading of the application programs can only be done via CAN1. Gold plated, locked and sealed connectors: Pins of this kind are used to measure analog signals. There are two bit variables associated with each pin of this type in PLCopen programming environment. Monitoring the state of the pin is generally not possible when the pin is used as a PWM signal output.
Otherwise operation of other inputs may be interfered Note 3: This product is designed to be used only for machine controlling purposes. These parameters depend on software cycle time Note 4: The Mini module and the Mini display need the Hub module in order to have the full transient immunity. In low impedance current input configuration they are subject to damage if they are connected to for example 24 volt system voltage. Epec Oy reserves a right to improve its products without a further notice.
The first is one of the QX output bits for controlling the pin as an output. The buyer shall attach to the claim a possible error report or equivalent explanation of the grounds for the claim. The manufacturer gives the warranty of twelve 12 months to the products and thereto related firmware from commissioning or eighteen 18 months from the date of delivery of the products which ever occurs first The manufacturer is during the warranty period responsible for defects in the products and thereto related firmware resulting from faults in material, design or workmanship.
All claims with respect to defects in the products shall be made to the manufacturer without delay and no later than on the seventh 7th day after the defect has been or should have been discovered by the buyer.
Test method ISOpulse 5?
Even if some of the inputs were not used for frequency measurement or pulse counting, these conditions must nevertheless be respected regarding those inputs too. Neither does the warranty cover the expenses of sending devices to or elec the manufacturer for repairs.
The manufacturer shall, at its sole option, repair the products at its manufactory in Sein? The manufacturer gives no other warranties whatsoever for the products than the warranty set out in wpec section and thus the warranty given in this section sets forth the warranty given by the manufacturer in its entirety.
Please refer CoDeSys 2.
Excavator Spare Parts for SANY EPEC 2024 Control Module
No scrapping fee will, however, be charged for products that are received by the manufacturer during the warranty period.
The warranty does not cover possible expenses relating to travelling, accommodation, daily benefits, etc. The pairing is done in application program. The shunt resistor is used to measure the current flowing through the load. The system should be designed and constructed according to the Epec general mounting and cabling instruction document.
Recommended operating voltage 24 VDC? Some of the inputs are grouped: Please consult the manufacturer before using this pin as a module voltage supply. Module temperature Software deadlock is monitored by the hardware watchdog that reboots the module automatically after ms software deadlock.
Nominal supply voltage 24 VDC? CANopen for all physical buses?