Add Attachments to Content Item ‘ASTM D Glass Transition Temperature ( DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) . ASTM D Glass Transition Temperature (DMA Tg) of Polymer ASTM D has become a widely used test standard in many companies due to. ASTM D用DMA测试Tg_能源/化工_工程科技_专业资料。Designation: D – 07?1 Standard Test Method for Glass Transition.
|Published (Last):||3 July 2015|
|PDF File Size:||11.23 Mb|
|ePub File Size:||13.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Interpretation of Results This temperature is designated as TA. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Individual reprints single or multiple copies of this astn may be obtained by contacting ASTM at the above address or at phonefaxor service astm. It is the responsibility of the d702 of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Strains of less than 0.
D70228 on the analyzer, typical specimen asym can range from 56 6 4 3 12 6 1 3 2. Typically the thermocouple should be as d70028 to the sample as possible.
The equipment must be calibrated in the same loading mode as will be used for testing, either dual cantilever or three-point bending. The values given in parentheses are non-standard mathematical conversions to common units that are provided for information only. A non-standard specimen con? It is ideal because the glass transition is clearly displayed. For comparison purposes the peak temperature of the tangent delta curve Tt is identi?
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Precision and Bias 4 Sampling and Test Specimens 8.
In this example the transition is less clear than the thermogram of Fig. The temperature at which a signi?
Specimen absolute size is not? The two tangent lines are intersected, and temperature corresponding to this intersection point is recorded as the DMA Tg. A meaningful comparison of data requires that the specimen con? The DMA Tg value is astj used to indicate the upper use temperature of composite materials, as well as for quality control of composite materials.
These averages allow a relative comparison of the repeatability within laboratory precision and reproducibility between laboratory precision of the DMA Tg test parameters.
It is standard that one of the major? The maximum time between cure lamination and testing shall be 30 days, after which, prior to testing, specimens shall be oven-dried in accordance with Examples are shown in this appendix to provide graphical illustrations of how to select the two tangent lines.
D028 Method E speci? Before the transition the storage modulus is relatively constant, the sigmoidal change during transition is clear, and after the transition the storage modulus is relatively constant.
Weigh the specimen after the test to the nearest milligram 0. If a non-standard frequency, or the resonance mode, is used, the non-standard approach f7028 be described in the report and the test result recorded as non-standard.
Other materials, such as neat resin, may require non-standard deviations from this test method to achieve meaningful results. Current edition approved Dec.
ASTM D7028 – 07(2015)
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
During the glass transition, the storage modulus of the composite material is signi? The values given in parentheses are non-standard mathematical conversions to common units that are provided for information only. Opposite surfaces must be essentially 7d028 and intersecting surfaces perpendicular.
Measure the specimen length to 0. These values indicate that the material factors did not have a signi? Historical Version s – view previous asm of standard.
Laminate edges or other irregularities created in the laminate by mold or bagging techniques dd7028 be avoided. The conditioned specimens shall be tested within 30 minutes after removal from the conditioning chamber, or stored in sealed MIL-PRF or equivalent aluminized bag until test. Any deviations from the standard orientation shall be reported and the test results noted as non-standard. Users of this standard are expressly advised that determination of the validity of any ashm patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
A number in parentheses indicates the year of last wstm. For example, a linear plot scale will result in a lower value of DMA Tg. Using the approach of this test method the intersection point is drawn as shown in Fig.
Allow the oven to cool before removing the specimen. Link to Active This link will always route to the current Active version of the standard.