ASTM A860 PDF

ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.

Author: Dour Mile
Country: Myanmar
Language: English (Spanish)
Genre: Automotive
Published (Last): 20 April 2014
Pages: 422
PDF File Size: 9.55 Mb
ePub File Size: 5.67 Mb
ISBN: 593-7-84759-930-9
Downloads: 80841
Price: Free* [*Free Regsitration Required]
Uploader: Kazrakree

Carbon steel WPHY 65 buttweld fittings, ASTM A WPHY GR 65 Pipe Fittings Manufacturer, Exporter.

These fittings are for use in high-pressure gas and oil transmission and distribution systems. After the removal of any cracks, the tees shall be re-examined by the original method. This abstract is a brief summary of the referenced standard. Materials and Manufacture 5. All base metal specimens shall be removed with the axis of the specimens longitudinal to the direction of primary metal?

In pallets, in plywood cases, in bulk. JIS G Carbon steel pipes for ordinary piping.

Notch Toughness Properties 8. In case of dissatisfaction with the results of the tests, the producer or supplier may make claim for a rehearing. Wrought austenitic and austenitic-ferritic duplex stainless steels without specific inspection requirements BS EN Butt-welding pipe fittings Part 4: The nickel content of the deposited weld metal shall not exceed 1.

  ALPINE IDA-X305 MANUAL PDF

How can I help you? NOTE 1—For purposes of identi? Link to Active This link will always route to the current Active version of the standard. All values are Maximum unless A range is stated.

A860 WPHY 65 PIPE FITTTINGS

JIS G Stainless steel pipes. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? One or more of the supplementary requirements may be speci? The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. The results shall conform to Table 1 for either a60 or Speci?

Cvenergy absorptionC; measured at? This specification does not require hydrostatic testing. Size, mm 10 7. There sults shall conform to Table 1 for either. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment. Within the text, the SI units are shown in brackets.

Only the side wall area of the tees need be examined. Rejection shall be reported to the producer or aatm promptly in writing. Within the text, the SI units are shown in brackets. If used on small? The values axtm in each system are not exact equivalents; therefore, each system must be used independently of the other. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving.

  IEC 60664-4 PDF

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The purchaser may specify in the order a speci? This examination shall be performed in accordance with a written procedure and shall be performed after? Rectangular specimen for thickness less than 5? Specimens 8a60 conform to 8a60 values of chemical composition and mechanical properties, namely: Transverse-weld tensile strength shall be reported in ksi.

ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.

asgm Section V, Nondestructive Examination. In case of con? And over, Sizes tested Section;min, specimen, thickness [7. Weld-metal specimens shall be specimens with the axis transverse to the weld seam.