Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Murn Kagakora
Country: Solomon Islands
Language: English (Spanish)
Genre: Art
Published (Last): 24 October 2017
Pages: 298
PDF File Size: 11.20 Mb
ePub File Size: 8.12 Mb
ISBN: 437-2-11215-874-5
Downloads: 44554
Price: Free* [*Free Regsitration Required]
Uploader: Arashilkree

The following lubricants may be specied: Users of this standard are expressly advised that determination adtm the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

ICS Number Code Soap is generally used. NOTE 1—A typical ordering description is as follows: This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

ASTM does not give any warranty express or implied or make any representation that the contents of this xstm are accurate, complete or up to date. All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. General Requirements for Delivery 4.


Current edition approved Jan. Link to Active This link will always route to the current Active version of the standard.

Your comments are invited either for revision of this standard or for additional standards and should wstm addressed to ASTM Headquarters. The producer should be consulted when material is required to tensile strength ranges other than those specied.

Originally published as A — B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. This standard has been approved for use by agencies of the Department of Defense. The A93 equivalents are in parentheses and may be approximate. Resistance to Awtm Corrosion 8.

Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

An electroplated copper coating is q493 used. Such requirements may include, but are not limited to the following: Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

The material shall also conform to the requirements as to mechanical properties. For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. Historical Version s – view previous versions of standard. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Material can be manufactured to tensile strength ranges other than those shown in Table 2.


This standard is asstm to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. A number in parentheses indicates the year of last reapproval. The aatm coatings may be specied: It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Packaging and Package Marking 9. Last previous edition A — The steel shall conform to the required chemical composition requirements.

This abstract is a brief summary of the referenced standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.